B-WAVETECH
  • Login/Register

    Login

    Connect with:
  • Home
  • Shop
  • Science
  • Get Started
    • FAQ
  • Testimonials
  • Videos
  • About Us
  • Home
  • Shop
  • Science
  • Get Started
    • FAQ
  • Testimonials
  • Videos
  • About Us
  • Shop
    • Home
    • Shop
    • Science
    • Get Started
      • FAQ
    • Testimonials
    • Videos
    • About Us
CALL US

TEL. 626-814-9300

FOLLOW US ON:

WE'RE SOCIAL

     
03 Sep

How To Manual: Set Up Instructions

by admin / 0 Comment

THE B-WAVETECH “HOW TO” MANUAL :


How to set up the B-WaveTech DL-9200 and DL-1000(Mini)

Recommended complimentary products:

-Pulley Ratchets

-Multi-program Timer

Assembly

Assembling your DL-9200, DL1000, is a short and simple process.

Remove the machine from the box, attach pulley ratchets (available from your local retailer) to the (2) eyebolts that are attached to the top plate (just below the dome)

Installing and Running DL-9200, DL-1000

For optimal results, and to keep your machine under warranty, we advise you to use it in the following way:

Start by making sure the DL9200, DL-1000 is hung vertically with the Dome towards the ceiling.

The bottom of the machine should be aligned with the top ‘canopy level’ of the plants; to achieve this it is recommended to use the ratchet pulleys, this also assures that it may be adjusted upwards as your plants grow.

It’s optimal to have the DL9200, DL-1000 as close as possible to the center of the growing area. It’s effects radiate out from the machine in a circular pattern, so putting it close to a wall will limit it’s effectiveness.

Run the DL9200, DL-1000(for 15 minutes on, 45 minutes off, every hour during the light cycle). You can use a multi program timer for this purpose.

Keep the DL9200, DL-1000 turned OFF during the dark cycle. Running while your growing space is dark stresses the plants and will put excessive wear on the unit.

After mounting plug the DL9200, DL-1000 to the timer, plug the timer to a working wall outlet, and you are done. It is highly recommended to use the machine throughout the whole life cycle of the plant, on order to get optimal results.

For best results it is recommended that the CO2 level be elevated to 2000 ppm. Also the plants can absorb more nutrients so you can up the level 300 ppm with no ill effects to the plants.

Note 1: Due to rotating parts at high velocity it is recommended to keep the unit away from animals and children. You should also be mindful of hair and loose clothing when working around the unit. Always unplug the unit before attempting to handle it in any way.

Note 2: For the same reasons as Note 1 intermittent sound and machine vibration are normal. Loud grinding or squealing noises are NOT normal, please contact our RMA department if you are experiencing either of these.


Cleaning the unit

To clean the Mini use a lint less cloth and mild hand soap and water. Do not use Acetone ,Windex ,or other solvents, as it will scar the surface of the plastic.

Maintaining DL9200, DL-1000:

Although your BioWave machine is very easy to use, any machine with moving components requires periodic maintenance to ensure longevity and optimal performance.

At least every four months you need to service your machine, using the following procedure.

Disconnect the machine from the power source/ timer before performing maintenance.

It is recommended but not necessary to dismount the DL9200, DL-1000 from the pulleys, and place the machine horizontally on a table.

Remove the top dome using a 5/32” Allen wrench. And 7/16” socket

Locate all four bearings (they each use two bolts to fasten them to the polycarbonate plates), use a cotton swab or rag to remove any excess grease from the bearings.

Using a grease gun, locate the brass grease nipple on the side of each bearing. Using multi-purpose lithium grease, attach the grease gun to the grease nipple, and begin greasing. Apply 1oz. of grease, this is generally one ‘pump’ of the grease gun, do not over-grease this can result in bearing failure. Do not grease pressed bearings (the ones not being fastened by screws in the top plate and motor plate) these bearings are sealed and adding grease can cause issues.

If the grease flows out around the nipple it means that the nipple is clogged. Get a wrench or socket take the nipple off and take a paperclip or other wire and clean out the nipple. Blow through it to make sure it is no longer clogged and replace on the bearing.

Carefully put the lid back on to the machine. Be careful of electronics while putting lid back on.

NOTE: It is imperative to service your machine. Failure to do so will void your warranty.

Categories: Getting Started
Share on facebook Share on twitter Share on google

From the blog

11Feb

NEW from B-Wave Tech: GROgenieby admin / 0 comments

11Feb

NEWS FLASH – Devi Cannabis Wins 3rd Placeby admin / 0 comments

10Feb

BIOWAVE ON NETFLIXby admin / 0 comments

We are social!

Last Tweets

Recent Comments

Good stuff can't wait for the micro to come out good luck

mike on What’s New at B-wave

Had to try it. Seriously great machine.

Retroguy992 on Biowave DL-1000

CONTACT INFO

Call Us: 626-814-9300

FOLLOW US

     

  • Home
  • Shop
  • Science
  • Get Started
    • FAQ
  • Testimonials
  • Videos
  • About Us